Location:Home - Products
Products
Bluetooth/WiFi Combo - BDE-BW3301NxM2 (TI CC3301 Wi-Fi6 & BLE, -40°C to 105°C)
- BDE-BW3301NxM2 (TI CC3301 Wi-Fi6 & BLE, -40°C to 105°C)
-
- General DescriptionBDE-BW3301NPxM2 is a 2.4-GHz Wi-Fi 6 and Bluetooth Low Energy Combo wireless M.2 card based on TI’s 10th generation connectivity combo chip CC3301 which is based upon proven technology and complements the TI integrated devices for connectivity portfolio. This module is ideal for use in cost sensitive embedded applications with a Linux or RTOS host running TCP/IP, where the peak throughput requirement is 50 Mbps maximum at the IP layer. BDE-BW3301NPxM2 could be the best choice for bringing the efficiency of Wi-Fi 6 to embedded device applications with a small PCB footprint and highly optimized bill of materials with lower cost. The module integrates a BDE module (BDE-BW3301NP1 or BDE-BW3301NP2) on board, and provides a PCI Express M.2 interface to user, which is 2230 Key-E M.2 interface. It is designed for ease of use and integration to the embedded systems.
This module has two variants described as follows: BDE-BW3301NP1M2, single antenna port with U.FL connector; BDE-BW3301NP2M2, dual antenna port with U.FL connector, supports antenna diversity.
Key Features Highly optimized Wi-Fi 6 and Bluetooth Low Energy 5.2 system for low cost embedded IoT applications Seamless integration with TI SitaraTM MPU (Linux) / MCU+ (FreeRTOS) as well as other application processors 3-wire or 1-wire PTA for external coexistence with additional 2.4GHz radios (e.g. Thread or Zigbee) Multirole support e.g. STA and AP to connect directly with other Wi-Fi devices on different RF channels (Wi-Fi networks) Optional antenna diversity or selection (BDE-BW3301NP2M2) Operating temperature: -40°C to +85°C Wi-Fi 6® MAC, Baseband and RF Transceiver with support for IEEE 802.11 a/b/g/n/ax Wi-Fi6 Medium access controller (MAC) Hardware-based encryption and decryption using supporting WPA2 and WPA3 TWT and OFDMA for optimal embedded performance Application throughput up to 50 Mbps Supports 4-bit SDIO and SPI host interfaces Bluetooth® Low Energy 5.2 Bluetooth 5.2 supporting long-range and highspeed PHYs (up to 2 Mbps) Host controller interface (HCI) transport for Bluetooth with option for shared SDIO or UART Bluetooth Low Energy certified stack Integrated 2.4G-Hz PA for complete wireless solution with up to +20dBm output power Security Secured host interface Firmware authentication Anti-rollback protection Power Management VDD_1V8: 1.62 V - 1.98 V VDD_3V3: 2.1 V - 4.2 V Clock Source: On board 40 MHz XTAL fast clock External 32.768-kHz slow clock by default Interface and Form Factor PCI Express M.2 standard – 2230 Key-E 22 mm x 30 mm x 2.8 mm Regulatory (In Progress) FCC IC CE-RED Bluetooth SIG
Applications Grid Infrastructure Electricity Meter String Inverter Micro Inverter Energy Storage Power Conversion System (PCS) Building and Home Automation HVAC Controller HVAC Gateway Thermostat Building Security Gateway Garage door system IP network camera/ Video doorbell Wireless security camera Appliances Refrigerator & freezer Oven Washer & dryer Residential water heater & heating system Air purifier & humidifier Coffee machine Air conditioner indoor unit Vacuum robot Robotic lawn mower Medical Infusion pump Electronic hospital bed & bed control Multiparameter patient monitor Blood glucose monitor Blood pressure monitor CPAP machine Telehealth systems MRI Ultrasound scanner Ultrasound smart probe Electric toothbrush Retail Automation and Payment
Downloads
User Guide:
Enable_BDE-BW3301NP1_with_AM62x_User_Guide_V0.2.pdfRelated Products - Pre: BDE-BW3301x1 series(TI CC3301 2.4GHz Wi-Fi6 & BLE, -40°C to 105°C, tiny size）
- Next: BDE-BW3351xPx series(TI CC3351 2.4/5GHz Wi-Fi6 & BLE, -40°C to 105°C）
Copyright © 2021 BDE Technology. All rights reserved|Chicago, Illinois 60603