The BDE-MP2674P10 is a high performance multiprotocol 2.4-GHz wireless module supporting Thread, Zigbee®, Matter, Bluetooth® 5.3 Low Energy, IEEE 802.15.4g, IPv6-enabled smart objects (6LoWPAN), proprietary systems including TI 15.4-Stack (2.4-GHz), and concurrent multiprotocol through a Dynamic Multiprotocol Manager (DMM) driver. The module is optimized for low-power wireless communication and advanced sensing in buiding security systems, HVAC, medical, wired networking, portable electronics, and home theater & entertainment markets.

The BDE-MP2674P10 module is embeded with an powerful 48-MHz Arm® Cortex®-M33 processor with TrustZone® based secure key storage, device ID and trusted functions. The module has a low standby current of 0.92 μA with full 256 KB RAM retention, which enables longer battery life wireless applications. With its integrated PA, the module supports +20 dBm output power with best-in-class transmit current consumption at 101 mA for 2.4-GHz operation. This is suitable for the long-range and low-power applications. It is featured with the Low SER (Soft Error Rate) FIT (Failure-in-time) for long operational lifetime with no disruption for industrial markets with always-on SRAM parity against corruption due to potential radiation events. The device also has an autonomous ultra-low power Sensor Controller CPU with fast wake-up capability. As an example, the sensor controller is capable of 1-Hz ADC sampling at 1-μA system current.

The module has a software defined radio powered by an Arm® Cortex® M0, which allows support for multiple physical layers and RF standards. PHY and frequency switching can be done runtime through a dynamic multiprotocol manager (DMM) driver. The module supports +5 dBm TX at 9.8 mA in the 2.4-GHz band. It has a receive sensitivity of -104 dBm for 125-kbps Bluetooth® Low Energy Coded PHY.

The module integrates all required system-level hardware components including clocks, balun filter, other passives, and PCB trace antenna or U.FL connector into a small PCB form factor. It is for easy assembly and low-cost PCB design. 

The module is pre-certified with FCC, ISED, CE and Bluetooth SIG to make easy integration and fast time-to-market for customers.

In order to fullfil different application senarios, we privides different variants for users:

 BDE-MP2674P10A0 – with integrated PCB trace antenna, without on-module 32-Mbit SPI flash

 BDE-MP2674P10U0 – with integrated U.FL connector, without on-module 32-Mbit SPI flash

 BDE-MP2674P10N0 – with RFOUT pad for antenna, without on-module 32-Mbit SPI flash

 BDE-MP2674P10A32 – with integrated PCB trace antenna, with on-module 32-Mbit SPI flash

 BDE-MP2674P10U32 – with integrated U.FL connector, with on-module 32-Mbit SPI flash

 BDE-MP2674P10N32 –with RFOUT pad for antenna, with on-module 32-Mbit SPI flash

 

 

 Wireless microcontroller

 Powerful 48-MHz Arm® Cortex®- M33 processor

with TrustZone®

 FPU and DSP extension

 1024 KB flash program memory

 8 KB of cache SRAM

 256 KB of ultra-low leakage SRAM with parity for high-reliability operation

 32 kB of additional SRAM is available if parity is disabled

 Dynamic multiprotocol manager (DMM) driver

 Programmable radio includes support for 2-(G)FSK, 4-(G)FSK, MSK, Bluetooth® 5.3 Low Energy, IEEE 802.15.4 PHY and MAC

 Supports over-the-air upgrade (OTA)

 Ultra-low power sensor controller

 Autonomous MCU with 4 KB of SRAM

 Sample, store, and process sensor data

 Fast wake-up for low-power operation

 Software defined peripherals, capacitive touch, flow meter, LCD

 Low power consumption

 MCU consumption:

 4.0 mA active mode, CoreMark®

 83 μA/MHz running CoreMark®

 1.19 μA standby mode, RTC, 256 KB RAM

 0.13 μA shutdown mode, wake-up on pin

 Ultra low-power sensor controller consumption:

 30 μA in 2 MHz mode

 809 μA in 24 MHz mode

 Radio Consumption:

 6.4 mA RX

 7.3 mA TX at 0 dBm

 22 mA TX at +10 dBm

 101 mA TX at +20 dBm

 Wireless protocol support

 Thread, Zigbee®, Matter

 Bluetooth® 5.3 Low Energy

 SimpleLink™ TI 15.4-stack

 6LoWPAN

 Proprietary systems

 High performance radio

 -104 dBm for Bluetooth® Low Energy 125-kbps

 –105 dBm for IEEE 802.15.4-2006 2.4 GHz OQPSK (coherent modem)

 Output power up to +20 dBm with temperature compensation

 Regulatory compliance (On-going)

 FCC

 IC

 CE-RED

 Bluetooth SIG

 MCU peripherals

 Most digital peripherals can be routed to any GPIO

 Four 32-bit or eight 16-bit general-purpose timers

 12-bit SAR ADC, 200 kSamples/s, 8 channels

 8-bit DAC

 Two comparators

 Programmable current source

 Four UART, four SPI, two I2C, I2S

 Real-time clock (RTC)

 Integrated temperature and battery monitor

 24 GPIOs – none SPI flash versions

 20 GPIOs – SPI flash versions

 Security enablers

 Supports secure boot

 Supports secure key storage and device ID

 Arm TrustZone for trusted execution environment

 AES 128- and 256-bit cryptographic accelerator

 ECC and RSA public key hardware accelerator

 SHA2 Accelerator (full suite up to SHA-512)

 True random number generator (TRNG)

 Secure debug lock

 Software anti-rollback protection

 Operating range

 On-chip buck DC/DC converter

 1.8 V to 3.8 V single supply voltage

 -40 to +85°C

 Antenna

 PCB antenna – BDE-MP2674P10A

 U.FL connector – BDE-MP2674P10U

 ANT Pad – BDE-MP2674P10N

 On-Module SPI Flash

 32-Mbit, only available in SPI flash versions

 Package

 Dimension: 26 mm x 19 mm x 2.15 mm

 LCC-42

 RoHS-compliant package

 

 2400 to 2480 MHz ISM and SRD systems with down to 4 kHz of receive bandwidth

 Building automation

 Building security systems – motion detector, electronic smart lock, door and window sensor, garage door system, gateway

 HVAC – thermostat, wireless environmental sensor, HVAC system controller, gateway

 Fire safety system – smoke and heat detector, fire alarm control panel (FACP)

 Video surveillance – IP network camera

 Elevators and escalators – elevator main control panel for elevators and escalators

 Industrial transport – asset tracking

 Factory automation and control

 Medical

 Personal care & fitness

 Patient monitoring & diagnostics – medical sensor patches, multiparameter patient monitor

 Medical equipment

 Home healthcare – blood glucose monitor, pulse oximeter

 Electronic point of sale (EPOS) – Electronic Shelf Label (ESL)

 Communication equipment

 Wired networking – wireless LAN or Wi-Fi access points, edge router 

 Personal electronics

 Portable electronics – RF smart remote control

 Home theater & entertainment – smart speakers, smart display, set-top box

 Connected peripherals – consumer wireless keypads

 Gaming – electronic and robotic toys

 Wearables (non-medical) – smart trackers, smart clothing

Datasheet: BDE-MP2674P10_Datasheet_V0.1.pdf